DSpace Community: Науковий журнал
http://elar.nung.edu.ua/handle/123456789/22
Науковий журнал2024-03-28T17:21:55ZDevelopment of a polymer matrix with improved performance characteristics for protection of vehicle elements
http://elar.nung.edu.ua/handle/123456789/9228
Title: Development of a polymer matrix with improved performance characteristics for protection of vehicle elements
Authors: Brailo, M. V.; Buketov, A. V.; Yakushchenko, S. V.; Sapronova, A. V.; Kobelnyk, O. S.; Yarema, I. T.; Fesenko, I. P.
Abstract: The impact of Norsodyne O 12335 AL polyester resin content in epoxy oligomer ED-20 in terms of thermophysical properties has been investigated. The dynamics of the heat resistance index (according to Martens) of the composite with the increasing content of polyester resin in the epoxy oligomer to q= 120 weight parts and the optimal polyester binder content have been established. The change of thermal coefficient of linear expansion of epoxy-polyester composite in different temperature ranges and linear shrinkage from polyester resin content have been studied.; У роботі досліджено вплив вмісту поліефірної смоли Norsodyne O 12335 AL у епоксидному олігомері
ЕД-20 за показниками теплофізичних властивостей. Проаналізовано динаміку показника термостійкості (за Мартенсом) композиту при збільшенні вмісту поліефірної смоли у епоксидному олігомері до q = 120 мас.ч. та встановлено оптимальний вміст поліефірного зв’язувача. Досліджено зміну показників термічного коефіцієнту лінійного розширення (ТКЛР) епоксиполіефірного композиту у різних температурних діапазонах та лінійну усадку від вмісту поліефірної смоли.2020-01-01T00:00:00ZThe study of the influence of technological parameters of the impulse process on the formation of the weld metal and the microstructure of the heat-affected zone
http://elar.nung.edu.ua/handle/123456789/9227
Title: The study of the influence of technological parameters of the impulse process on the formation of the weld metal and the microstructure of the heat-affected zone
Authors: Maksymov, S. Yu.; Gavryliuk, A. A.; Shlapak, L. S.
Abstract: With prolonged operation of metal structures, the likelihood of their mechanical destruction increases. This also applies in many respects to the welded joints of main pipelines. One of the promising ways of solving the issue of increasing their service life is the development of welding methods based on the use of pulse control of process energy parameters. Pulse welding mode allows for controlled heat input into the welded joint zone, control of the electrode metal melting mode, formation of the weld metal structure and heat-affected zone (HAZ).Two types of metal transfer from the electrode to the weld pool were used in the work: with short circuits and without them, that is, welding was carried out on a "long" arc. At a constant electrode wire feed rate, the welding mode was changed by changing the shape of the current-voltage characteristic of the power source.; При тривалій експлуатації металевих конструкцій збільшується вірогідність їх механічного руйнування. Це значною мірою стосується і зварних з'єднань магістральних трубопроводів. Одним з перспективних шляхів розв’язання питання підвищення терміну їх експлуатації є розробка методів зварювання, заснованих на використанні імпульсного керування енергетичними параметрами процесу. Імпульсний режим зварювання дозволяє здійснювати регульоване тепловкладення в зону зварного з'єднання, керувати режимом плавлення електродного металу і формуванням структури металу шва та зони
термічного впливу (ЗТВ). В роботі застосовувалося два види переносу металу з електроду в зварювальну ванну: з короткими замиканнями та без них, тобто виконувалось зварювання на "довгій" дузі. При постійній швидкості подачі електродного дроту режим зварювання змінювали шляхом зміни форми вольт-амперної характеристики джерела живлення.2020-01-01T00:00:00ZPolymeric materials based on epoxy oligomer DER-331 and hardeners ofdifferent physical and chemical nature for repairing of gas production equipment
http://elar.nung.edu.ua/handle/123456789/9226
Title: Polymeric materials based on epoxy oligomer DER-331 and hardeners ofdifferent physical and chemical nature for repairing of gas production equipment
Authors: Sapronov, O. O.; Sotsenko, V. V.; Antonio, B.; Smetankin, S. O.; Yurenin, K.Yu.
Abstract: The optimal content of PEPA and TETA hardeners and polymerization temperature during matrix formation on the basis of epoxy oligomer DER-331 were determined. The dynamics of dependence of hardener content on physical and mechanical properties of epoxy matrix was investigated. According to the results of the study, materials with the optimal content of hardener and temperature range of polymerization for the formation of a composition with high physical and mechanical properties and its further use for the repair of gas equipment are proposed.; Визначено оптимальний вміст твердників поліетиленполіамін (ПЕПА) і триетилентетрамін (ТЕТА) та
температури полімеризації при формуванні матриці на основі епоксидного олігомеру DER-331. Досліджено динаміку залежності вмісту твердника на фізико-механічні властивості епоксидної матриці. Згідно отриманих результатів дослідження запропоновано матеріали з оптимальним вмістом твердника та температурного режиму полімеризації для формування композиції з підвищеними фізико-механічними
властивостями ї її подальшого використання для ремонту газопромислового обладнання.2020-01-01T00:00:00ZAdaptation of the material balance of a gas deposit
http://elar.nung.edu.ua/handle/123456789/9225
Title: Adaptation of the material balance of a gas deposit
Authors: Zarubin, Yu.; Hunda, M.; Mamus, P.
Abstract: The aim of the research is to study the application of the material balance method with modern technologies to create a useful gas reservoir model with water influx.The basic equations of material balance are analyzed taking into account the Mendeleev–Clapeyronlaw for gases. The analysis was performed taking into account the water influx component according to Fetkovich equations. The paper highlights the problems of identifying the parameters of the material balance model as material balance model doesn’t include the geological structure of deposits. The calculation was done by material balance models created on Mathcad and VBA Excel.; Метою роботи є дослідження застосування методу матеріального балансу із використанням сучасних
технологій для створення адекватної моделі газового пласта з активним поступленням води. Проаналізовано основні рівняння матеріального балансу з урахування закону Менделєєва–Клапейрона
для газів. Аналіз проведено з урахуванням активної водонапірної складової за рівняннями Фетковича. У
роботі висвітлено проблематику оцінювання параметрів моделі матеріального балансу, оскільки останній не містить уявлення про геологічну структуру покладу. Розрахунки виконано на основі створених моделей покладу у MathCad та за допомогою VBA Excel.2020-01-01T00:00:00Z